Comings and Goings

Replacing A’van Tail Lamps

The tail lamps installed on my (2009) A’van Cruiser are horrid. They use festoon bulbs, which are totally unreliable. Festoon bulbs rely on feeble spring pressure to stay in place and to deliver the necessary current. If water gets in, the contacts will rust and the lamps will stop working.

I have looked for several years for a suitable replacement using sealed LED lamps, but could find nothing that would fit in the hole (everything was either too big or too small). What I have been looking for is 100mm surface-mount LED lamps. They have to be surface-mount because there is no easy way to get to the other side of the fibreglass panel.

The search came to an end when I discovered 95mm round surface-mounted lamps at LED Autolamps in the UK. A company with the same name exists in Australia but does not seem to carry these lamps. An added benefit of these lamps is that they are sealed (waterproof).

Here’s what I ordered:

  • 2 x 95RME Multivolt 95mm Round Stop/Tail Light (about $32 each ex VAT)
  • 2 x 95AME Multivolt 95mm Round Indicator Light (about $32 each ex VAT)
  • 4 x 95BKT Surface Mount Bracket for 95mm Round Lights (about $6 each ex VAT)
  • International airmail postage about $30

The company is very efficient and everything arrived exactly 7 days after I placed my order.

Other materials used:

  1. Waterproof crimp joiners (Red, 3mm from Super Cheap Auto). These should also be available from Repco or Jaycar.
  2. Self-tapping 6 or 8-gauge screws about 12mm long, to attach the mounting brackets for the new lamps.
  3. Silicon sealer.

Tools (in addition to the usual screwdrivers, drills and the like):

Crimping tool

Dividers

Pair of compasses

Heat gun

  1. Crimping tool (which should include a wire stripper)
  2. Dividers
  3. Pair of compasses (or compass for those born after 1950)
  4. Heat gun or gas soldering iron (to seal the waterproof crimp joiners). Hair dryer might work.

Remove the old lamps:

  1. Remove the lens from the old lamp and remove the bulbs.
  2. Snip the wire leads attached to the terminals (don’t bother to unscrew them, it’s better to have freshly stripped wires for crimping). Don’t be tempted to push the leads back behind the fibreglass body of the van, because they will be unbelievably difficult to get back.
  3. Remove the two screws attaching the chrome bezel to the caravan body.
  4. The bezel will be stuck to the body with silicon sealant. Use a screwdriver to gently ease the bezel away from the body. Use a piece of cardboard or folded cloth to protect the fibreglass panel from the shaft of the screwdriver.
  5. Use the blade of the screwdriver to remove remaining silicon sealant from the surface of the caravan panel. Use a thin screwdriver to remove silicon sealant from around and inside the hole in the panel to free the wires so they will be free to be pushed back in at a later step. Don’t push them back in the hole yet! Thoroughly clean the surface of the panel in the tail lamp depression.
  6. You need to enlarge the hole through which wires protrude because the cable attached to the new lamp will need to be pushed through later and it is too thick to fit. I drilled another hole of a similar size below the original then used a file to join the two and open it out a bit.Take care not to damage the wires.

Removing the bezel

 

Attach the mounting brackets:

  1. The next trick will be to find the centre of the circular depression in which the lamps will be installed. In some cases there may be a mark left by the old lamp, but there is no guarantee these were placed centrally in the first place. I used a pair of dividers to draw three arcs of slightly greater radius than the radius of the circular depression. These arcs will intersect at or near the centre of the circle. The arcs will probably form a small triangle; it should be easy to guess from here.
  2. You can check that you have found the centre: open the dividers to about 63mm (half the diameter of the base of the depression, about 125mm), and swing a circle about the “centre” you have found. It should be a millimetre or two from the edge all the way round. If not, move your “centre”.
  3. The mounting brackets have a 45mm diameter hole in the centre and a drain hole along the outer edge. The drain hole must be at the bottom when the bracket is mounted.
  4. I used a pair of compasses to draw a 45mm diameter (22.5mm radius) circle centred on the point found in step 1. Align the 45mm diameter hole in the mounting bracket to the 45mm diameter circle drawn in the circular depression. Ensure the drain hole is at the bottom and the mounting screws for the LED lamp are horizontal. There are 4 mounting holes in the base of the mounting bracket; carefully mark their positions on the panel.
  5. Drill holes in the panel big enough to take the mounting screws. Screw the mounting bracket to the panel and check that it is aligned correctly (with the drain hole at the bottom).
  6. If it looks OK remove the bracket and apply a bead of silicon sealant around the base and around the screw holes. Reattach the bracket with the drain hole at the bottom. Remove any excess silicon sealant.

Mounting bracket

Install the new lamps:

  1. With the exception of the left-hand indicator, the wire colours on the lamps will match those protruding from the holes in the panel. The left-hand indicator hole will have a yellow wire that needs to be attached to the green wire at the back of the new lamp.
  2. The old stop/tail light has two white (earth) wires. One of these can be snipped off, because it is not needed. The snipped one can probably just safely float around, but I folded mine over and sealed it with a small piece of heat-shrink tubing, just to be certain.
  3. Strip enough insulation from the wires to allow the conductors to reach the middle of the joiners. If the copper wire has corroded (the strands are black instead of shiny pink) you need to clean them.
  4. Check that the stripped wire fits the joiners. If the wires coming out of the body are too fat, snip off a few strands until they slide in easily. (The current used by the LED lamps is about 10% of that used by the incandescent lamps, so skinny wire is OK).
  5. Connect corresponding wires using the crimp joiners. Double-check that you have each wire on the lamp connected to the matching coloured wire coming out of the hole in the body. If you used waterproof joiners then you will need to use a heat gun to shrink the plastic covers on the joiners (the gas soldering iron with the tip removed will do the job).
  6. Connect the caravan to the car and test the lamps. If all is OK screw the lamps into place. You will need to push most of the cable down the enlarged hole to make this work. You might want to apply some silicon sealant around the cable hole to keep any water out.
  7. Test the lamps again.

Indicator lamp installed

New lamps working

 

Print Friendly, PDF & Email

One thought on “Replacing A’van Tail Lamps

  1. Andrew marley

    Hi have been investigating replacing the awful festoon lights on my brand new cruiseliner. Found hella make a 110 mm light assembly.. I just don’t understand Avan using such cheap crap. I virtually had to re crimp every joint when I took delivery. There were even fuses missing. All my complaints fell on deaf ears.

    Cheers

Leave a Reply

Your email address will not be published. Required fields are marked *